April 05, 2017 05:32PM
|
|
Admin
Registered: 15 years ago
Posts: 944 : Lake Havasu City, Arizona |
Suffering from the failed antenna drive so found one from salvage, it too had the same problem. Motor runs but no motion. Disassembled and found broken belts in both. So I went online and eventually found what appears to be a source for replacement. Unfortunately the belts are not expensive but the minimum order value and minimum shipping cost drive the cost way up. So, I ordered several so the cost each was not so bad.
So, if anyone wants one, I could share for a reasonable price. Should have in hand end of next week. Bob in Lake Havasu |
April 19, 2017 06:41PM
|
|
Registered: 15 years ago
Posts: 797 : Ottawa |
April 20, 2017 09:26PM
|
|
Admin
Registered: 15 years ago
Posts: 944 : Lake Havasu City, Arizona |
Ferdinand,
I would be happy to mail you one for $7 postage included. The list price online is $4 but with the minimum order size charge and shipping I have almost $6 in each. I have installed one so far but the new belt appears to be about one millimeter shorter than the old belt and I had to elongate the mounting holes for the motor to put it on with out excessive tension. Does work though. just took a little work with a small rat tail file. Let me know if the price is ok. I probably should make a video of the process. It is not difficult to figure out though. Bob in Lake Havasu |
April 21, 2017 10:01AM
|
|
Registered: 15 years ago
Posts: 797 : Ottawa |
April 21, 2017 10:39PM
|
|
Admin
Registered: 15 years ago
Posts: 944 : Lake Havasu City, Arizona |
April 21, 2017 10:45PM
|
|
Admin
Registered: 15 years ago
Posts: 944 : Lake Havasu City, Arizona |
April 24, 2017 07:03PM
|
|
Admin
Registered: 15 years ago
Posts: 944 : Lake Havasu City, Arizona |
Drive belt replacement.
The new belt is about 1.5 mm shorter than the old one. See attached picture. 1. lift the two prongs off the motor mounting casting and rotate the clip out of the away. 2. Remove the two large phillips screws and lift out the motor mount leaving the motor attached to the wires. 3. Remove the two smaller phillips screws holding the motor to the cast mounting. 4. discard the belt adjustment cam. 5. Using a small rat tail file elongate the motor mounting holes so the motor can be about 1.5 mm closer to the large pulley. Do not just make the holes bigger as the screws will then need washers. When assembled with the new belt, the motor should turn freely by hand with no binding. If not, elongate the holes a small amount more. Bob in Lake Havasu |
May 11, 2017 03:25PM
|
|
Registered: 15 years ago
Posts: 797 : Ottawa |
That belt adjustment cam is pretty clever. The hole for the motor is offset from the centre.
[attachment 237 belt-1.jpg] Mounted with the cam turned this way, tightens the belt. [attachment 238 belt-2.jpg] Or with the cam turned this way, it loosens the belt. Seems simple enough. [attachment 239 belt-3.jpg] Except, nothing's ever simple... The new belt is just that little bit too tight. So I did as Bob suggested, and elongated the mounting holes for the motor allowing it to be positioned slightly closer to the big sprocket. I only had one small misadventure. While I had the case open, I figured I'd take the whole gizmo apart to give everything a good cleaning. When taking the C-clip off the centre shaft, of course the little thing when zinging over my shoulder to land in the driveway behind me. I saw approximately where it went, but that damn C-clip is the exact same colour as the blacktop in my driveway, so it took me nearly half an hour on my hands and knees crawling around the driveway before I found it again. D'oh! Otherwise, mission accomplished. The radio antenna goes up and down again. Yippee! |
May 17, 2017 05:50PM
|
|
Admin
Registered: 15 years ago
Posts: 944 : Lake Havasu City, Arizona |